![]() You cannot reload from a virtual terminal if the system is not set up for automatic booting. Use the reload command after configuration information is entered into a file and saved to the startup configuration. If the system is set to restart on error, it reboots itself. This command was introduced on the Cisco ASR 1000 Series Aggregation Services Router and was made available in diagnostic mode. The reason keyword and reason-string argument were added. This command was integrated into Cisco IOS Release 12.2(28)SB. The file keyword and url argument were added. Support for this command on the Supervisor Engine 2 was extended to Release 12.2(17d)SXB. The / verify and /noverify keywords were integrated into Cisco IOS Release 12.3(4)T. The / verify and /noverify keywords were integrated into Cisco IOS Release 12.0(26)S. The Cisco 7500 series router in not supported in Cisco IOS Release 12.2(20)S. ![]() Support was added for the Cisco 7304 router. The / verify and /noverify keywords were added. This command was integrated into Cisco IOS Release 12.2(18)S. Support for this command was added for the Supervisor Engine 720. (Optional) Specifies a reason for reloading. (Optional) Number of the day in the range from 1 to 31. The reload must take place within 24 days. Specifying 00:00 schedules the reload for midnight. If you do not specify the month and day, the reload takes place at the specified time on the current day (if the specified time is later than the current time) or on the next day (if the specified time is earlier than the current time). If you specify the month and day, the reload is scheduled to take place at the specified time and date. (Optional) Schedules a reload of the software to take place at the specified time (using a 24-hour clock). The reload must take place within approximately 24 days. (Optional) Schedules a reload of the software to take effect in the specified minutes or hours and minutes. (Optional) Reason for reloading the string can be from 1 to 255 characters long. (Optional) Specifies the image file for warm rebooting. Note This keyword is often issued if the file verify auto command is enabled, which automatically verifies the digital signature of all images that are copied. (Optional) Does not verify the digital signature of the file that will be loaded onto the operating system. (Optional) Verifies the digital signature of the file that will be loaded onto the operating system. Reload ] | at hh : mm ] | reason | cancel ] Syntax Description To reload the operating system, use the reload command in privileged EXEC or diagnostic mode. The following example shows how to optimize the compilation of regular expression access list: Router# configure terminalĬreates an entry in a cache profile group that allows authentication and authorization matches based on a regular expression. This command was implemented on the Cisco ASR 1000 Series Aggregation Services Routers. This command was integrated into a release earlier than Cisco IOS Release 12.2(33)SXI. This command was integrated into a release earlier than Cisco IOS Release 12.2(33)SRC. This command was introduced in a release earlier than Cisco IOS Release 15.0(1)M. Global configuration (config) Command History This command has no arguments or keywords. To disable the configuration, use the no form of this command. ![]() ![]() To optimize the compilation of a regular expression access list, use the regexp optimize command in global configuration mode. ![]() Refuse-message /The dial-out modem is currently in use. In the following example, line 5 is configured with a line-in-use message, and the user is instructed to try again later: line 5 When you define a message using this command, the Cisco IOS software performs the following steps: You cannot use the delimiting character within the text of the message. Then enter one or more lines of text, terminating the message with the second occurrence of the delimiting character. This command was integrated into Cisco IOS Release 12.2(33)SRA.įollow this command with one or more blank spaces and a delimiting character of your choice. You cannot use the delimiting character in the message.ĭisabled (no line-in-use message is displayed). To disable the message, use the no form of this command.ĭelimiting character of your choice-a pound sign (#), for example. To define and enable a line-in-use message, use the refuse-message command in line configuration mode.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |